It’s only been out for a month, but now, thanks to the efforts of veteran racer Dave Thomas; the 2011 Dodge Challenger Drag Pak (Mopar’s spelling not ours), has blazed into the history books.

During a test session at Atco Raceway in New Jersey last week, in preparation for the NHRA Division 1 National Open; Thomas rattled off an Elapsed Time of 9.43 seconds at 143.90 mph in the quartermile, setting a new fastest record in the process.

Thomas, who’s been drag racing since 1971, took delivery of his turn-key drag spec Challenger just two weeks prior. Powered by a version of the Viper’s 500 cubic inch V-10 and equipped with a two-speed drag transmission and solid rear axle, plus a competition fuel system; Thomas says the only changes from what Mopar offers out of the box were adding weight bars.

“It’s a spectacular car,” he said. “On its first-ever run, the car went a 9.79 at 137 mph. It’s a turn-key operation. There are no headaches involved in setting it up at all. You just get in there and drive it. It’s neat that the factory can make something like this.”

After the success of Ford’s 2008 Mustang Cobra Jet, Ford announced at the 2009 Specialty Equipment Manufacturers Association (SEMA) Show the return of the car for 2010. In a “SEMA Special” silver with a charcoal Cobra Jet graphics package, the new turnkey race car is ready for NHRA competition.

“The 2008 Cobra Jet was a great car, it did everything we wanted it to do,” said Brian Wolfe, director, Ford North American Motorsports. “We’re really proud of the car, but then again we’re always trying to make the next one better. With the 2010 Cobra Jet, we had the luxury of a longer development cycle and the result is absolutely stunning. Where the 2008 Cobra Jet was an extremely potent starting point for NHRA Stock competition, the 2010 will enhance the car further. We are all excited to see the new Cobra Jet in competition.”

The new model uses a 425-hp supercharged 5.4-liter V8 direct from the Ford Racing Performance Parts catalog. Ford also plans to make another engine available, with an aluminum block and 475-hp. A six-speed manual transmission (the same found in the ‘08 model) will be standard equipment, however, there will be an option to upgrade to a 5-speed Liberty manual unit or a race-spec auto-box. In addition, the Cobra Jet will get an NHRA certified roll cage and lightweight racing brakes. The car will also get launch control.

Only 50 2010 CJs will be built.

GALLERY: 2010 Ford Mustang Cobra Jet

Official release after the jump:

PRESS RELEASE

2010 COBRA JET MUSTANG CONTINUES THE EVOLUTION OF TURNKEY RACE CAR PROGRAM

2010 Ford Mustang Cobra Jet

LAS VEGAS, Nov. 3, 2009 – Since its victorious introduction at the NHRA Winternationals in 1968, Ford’s Cobra Jet Mustang has created a legacy of power, performance and triumph.

The 40th Anniversary 2008 Cobra Jet Mustang lived up to the legend of the original, duplicating the NHRA Winternationals victory in 2009 and dominating drag strips across the land.

Today, Ford Racing unveiled the 2010 Cobra Jet Mustang at the Specialty Equipment Market Association (SEMA) show, which marks the continued evolution of the CJ as a factory-produced turnkey race car. In honor of the SEMA introduction, Ford Racing built and unveiled a one-of-a-kind “SEMA Special” silver Cobra Jet complete with a charcoal Cobra Jet graphics package.

“The 2008 Cobra Jet was a great car, it did everything we wanted it to do,” said Brian Wolfe, director, Ford North American Motorsports. “We’re really proud of the car, but then again we’re always trying to make the next one better.

“With the 2010 Cobra Jet, we had the luxury of a longer development cycle and the result is absolutely stunning. Where the 2008 Cobra Jet was an extremely potent starting point for NHRA Stock competition, the 2010 will enhance the car further. We are all excited to see the new Cobra Jet in competition.”

For decades, the Mustang has been the preeminent car in many forms of racing, including drag racing. The 2008 Cobra Jet Mustang added to that legacy this season with high- profile wins at the NHRA Winternationals and U.S. Nationals, and by setting numerous track records across the country.

The 2010 Cobra Jet, like its predecessor, is a factory-built race car that is intended for NHRA Stock and Super Stock racing. The goal for the 2010 Cobra Jet was to enhance the race features to further make its own place in NHRA history. The 2010 CJ will come with all of the features of the 2008 car with enhancements that include options for a full race-prepared automatic or manual transmission, drag race-specific shocks and springs, manual steering and brakes, 8.50 certified rollcage, and an Aeromitive return-style fuel system with trunk-mounted fuel cell.

Additionally Ford Racing engineers have developed for the 2010 Cobra Jet a factory-first launch control/rev limiter that will allow drivers to preset the rpm after they stage the car. When they are ready to leave, all they do is put the throttle pedal to the floor; they don’t have the engine speed to free rev. Previously, the launch control/rev limiter was only available as an aftermarket option.

Much like Ford Racing’s previous Mustang FR500S race car, the Cobra Jet Mustang will get its start at the Auto Alliance International (AAI) assembly plant in Flat Rock, Mich. The entire 50-car run of 2010 Cobra Jets will be built on the same production line that produces the 2010 Ford Mustang production car. Production of Cobra Jets will commence in January, with delivery of all vehicles expected in the first quarter of 2010.

All of the additional parts and pieces for the CJ can be found in the Ford Performance Parts catalog. And since the Cobra Jet is produced from a base V-6 Mustang, any consumer can turn his Mustang into a Cobra Jet by purchasing the parts from the Ford Performance Parts catalog.

The 2010 CJ car features a choice for customers between two supercharged engines or three normally aspirated engines (pending NHRA approval). These options will allow the Cobra Jet to be eligible for more classes in the NHRA, as well as competition with other sanctioning bodies, including NMRA, NMCA, PSCA and IHRA.

All 50 of the 2010 Cobra Jet Mustangs have already been ordered by Ford dealers for delivery to customers. For those customers who missed out on the limited run of 2010 Cobra Jets, Ford Racing has set a goal to provide future versions of the Cobra Jet.

After the success of Ford’s 2008 Mustang Cobra Jet, the company has announced plans to bring back the factory drag racer using the new 2010 platform.

The new model will use a 425hp supercharged 5.4-liter V8 direct from the Ford Racing Performance Parts catalog. Ford also plans to make another engine available, with an aluminum block and 475hp. A six-speed manual transmission (the same found in the ’08 model) will be standard equipment, however, there will be an option to upgrade to a 5-speed Liberty manual unit or a race-spec auto-box.

In addition, the Cobra Jet will get an NHRA certified roll cage and lightweight racing brakes.

“I’ve said from my first day in this job that I wanted Ford Racing to continue to be a ‘racer-friendly’ organization,” said Ford Racing boss Brian Wolfe. “That’s why we take great pride in being one of only two car companies worldwide that builds ready-to-race cars and sells them as part of our performance parts offerings.”

The 2010 Cobra Jet comes hot on the heels of the 2008 model (pictured above), which was created to celebrate the 40th anniversary of the original.

Only 50 Cobra Jets will be built, the exact number required by the NHRA in order for the vehicles to run in the series.

Pricing is expected to be in the $75,000 range with production in the Fall for delivery early 2010.

Official release after the jump:

PRESS RELEASE:

Milan, Mich. – The 40th Anniversary 2008 Mustang Cobra Jet more than lived up to its billing, joining its historic predecessor-the original 1968 Cobra Jet in winning its inaugural race at the NHRA Winternationals in Pomona, Calif. Now, Ford Racing is ready to update the latest Cobra Jet, and is announcing plans to build a 2010 version of the CJ. The announcement was officially made today at the National Mustang Racing Association event in Milan.

A little more than a year ago, Ford Racing announced plans to build a modern edition of the Cobra Jet. The limited run of 50 cars sold in less than two weeks, even before the first car was built. Once again Ford Racing will produce a limited run of 50 2010 Mustang CJs, the minimum number that must be produced in order to receive clearance from NHRA for competition.

Exact specifications are being finalized, but the initial plan is for the ’10 Cobra Jet to have a 425-hp 5.4-liter supercharged engine from the Ford Racing Performance Parts catalog, but with an option to upgrade to an estimated 475-hp aluminum block engine. Likewise the 6-speed manual transmission that was available in the ’08 Cobra Jet will be standard, but an option to upgrade to 5-speed Liberty manual transmission or a race prepped automatic transmission will be available. Other ’10 Mustang Cobra Jet upgrades include an 8.50et NHRA certified roll cage and lightweight racing brakes.

“I’ve said from my first day in this job that I wanted Ford Racing to continue to be a ‘racer-friendly’ organization,” said Wolfe. “That’s why we take great pride in being one of only two car companies worldwide that builds ready-to-race cars and sells them as part of our performance parts offerings.”

Component testing is underway and base pricing will be less than $75,000. Production is expected to begin during the fourth quarter with delivery expected in early 2010. Sportsmen racers interested in placing a pre-order for the ’10 Cobra Jet should contact their local Ford Dealership.